Legrand RC3APTCBK Manual do Utilizador descarregar pdf

IMPORTANT – PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.

Products Covered: RC3STC, RC3ATC, RC3ARTTC, RC3CTC, RC3CRTTC, and RC3SHTC

RC3ATC-LJB, RC3ARTTC-LJB, RC3ATCLJB25 and RC3ARTTCLJB25

CAUTION: Do Not operate tile stripper or resurfacing equipment over top of covers. This may result in damage to the surface finish of the product.

Suitable for use in air handling spaces in accordance with Sec. 300-22 (C) of the National Electrical Code.

Step 1. Layout and locate position of hole(s). Step 2. Remove 7" [178mm] dia. section from carpet

or tile. Use template provided.

CAUTION: Holes shall be spaced a minimum of 2' [610mm]

on center and not more than one hole per each

65 sq. ft. [6 sq. m] of floor area in each span.

For Tile Applications up to a Maximum of 3/4" [19.1mm] Thick.

NOTE: Be certain to drill hole at least 4" [102mm] from any wall NOTE: For tile thickness greater than 3/4" [19.1mm] consult factory.

or pillar to leave enough room for Poke-Thru cover assembly.

Step 3. Core drill hole. Step 4. Stem Assembly: Step 5. Cover Assembly:

Catalog No. RC3STC Catalog No. RC3CTC

Insert stem into hole. or RC3CRTTC. Remove

disposable plate and

replace with carpet/tile

flange. Install with four

#6-32 x 1/4" [6.4mm] FHMS.

24" [610mm] Min

Center – Center

[178mm] Diameter

CAUTION: Poke-Thru cannot be rotated

in hole after insertion into floor.

4" Diameter Core Drill

4 1/16" [103mm] Actual Diameter

Push Down

Four #6-32 x 1/4" FHMS

Poke-Thru Series

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 001 586 R2 – Updated April 2005

Wiremold Electrical Systems conform to and should be installed

and properly grounded in compliance with requirements of the

current National Electrical Code, Canadian Electrical Code or

codes administered by local authorities.

All electrical products may represent possible shock or fire

hazard if improperly installed or used. Wiremold electrical

products are UL Listed to U.S. and Canadian safety standards,

made for interior use only, and should be installed in conformance

with current local and/or the National Electrical Code.

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - Poke-Thru Series

IMPORTANT – PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.Products Covered: RC3STC, RC3ATC, RC3ARTTC, RC3CTC, RC3CRTTC, and RC3SHTC RC3ATC-LJB, RC3ART

Página 2 - Cover Plate Screw

COMPLETE ASSEMBLY: Step 6. Cat. Nos. RC3ATC or RC3ARTTC. Step 7. Wire the power circuit. Wire the Poke-Thru device. (Can be completed above floor.) R

Página 3

3Step 10. Wire and snap communication Step 11. Insert blanking plugs or neoprene foam jacks in adapters as shown. block in unused communication ports

Página 4

Step 14. Attach slide cover with two #6-32 screws. Step 15. Push Poke-Thru unit into concrete to complete installation. CAUTION: Do not over tighten

Página 5

The RC3TC Series Poke-Thru Device is UL Listed and Classified to U.S. and Canadian safety standards to the following conditions: The RC3STC Poke-Thru

Página 6 - CARPET CUTOUT TEMPLATE

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6

Modelos relacionados RC3APTCGY | BZTPP Series |

Comentários a estes Manuais

Sem comentários

Legrand RC3APTCBK Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Legrand RC3APTCBK. Legrand RC3APTCBK User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados RC3APTCGY | BZTPP Series |

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Legrand RC3APTCBK