Legrand RC4KTCBK Manual do Utilizador descarregar pdf

IMPORTANT – PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.

Products Covered: RC4ATC, RC4ARTTC, RC4CTC, RC4CRTTC, RC4STC, RC4SRTTC, and RC4SHTC

RC4ATC-LJB, RC4ARTTC-LJB, RC4ATCLJB25 and RC4ARTTCLJB25

CAUTION: Do Not operate tile stripper or resurfacing equipment over top of covers. This may result in damage to the surface finish of the product.

Suitable for use in air handling spaces in accordance with Sec. 300-22 (C) of the National Electrical Code.

Step 1. Layout and locate position of hole(s). Step 2. Remove 7" [178mm] dia. section from carpet

or tile. Use template provided.

CAUTION: Holes shall be spaced a minimum of 2' [610mm]

on center and not more than one hole per each

65 sq. ft. [6 sq. m] of floor area in each span.

For Tile Applications up to a Maximum of 3/4" [19.1mm] Thick.

NOTE: Be certain to drill hole at least 4 1/4" [108mm] from any wall NOTE: For tile thickness greater than 3/4" [19.1mm] consult factory.

or pillar to leave enough room for Poke-Thru cover assembly.

Step 3. Core drill hole. Step 4. Stem Assembly: Step 5. Cover Assembly:

Catalog No. RC4STC Catalog No. RC4CTC

Insert stem into hole. Remove disposable plate

and replace with carpet/tile

flange. Install with four

#6-32 x 1/4" [6.4mm] FHMS.

24" [610mm] Min

Center – Center

[178mm] Diameter

CAUTION: Poke-Thru cannot be rotated

in hole after insertion into floor.

4" Diameter Core Drill

4 1/16" [103mm] Actual Diameter

Push Down

Four #6-32 x 1/4" FHMS

Poke-Thru Series

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 001 636 R2 – Updated April 2005

Wiremold Electrical Systems conform to and should be installed

and properly grounded in compliance with requirements of the

current National Electrical Code, Canadian Electrical Code or

codes administered by local authorities.

All electrical products may represent possible shock or fire

hazard if improperly installed or used. Wiremold electrical

products are UL Listed to U.S. and Canadian safety standards,

made for interior use only, and should be installed in

conformance with current local and/or the National Electrical Code.

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - Poke-Thru Series

IMPORTANT – PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.Products Covered: RC4ATC, RC4ARTTC, RC4CTC, RC4CRTTC, RC4STC, RC4SRTTC, and RC4SHTC RC4ATC-L

Página 2 - Electrical Wiring Chart

COMPLETE ASSEMBLY: Step 6. Cat. Nos. RC4ATC or RC4ARTTC. Step 7. Wire the power circuit. See wiring diagram. Wire the Poke-Thru device. (Can be compl

Página 3

3Step 10. Communication Circuit Connections: Wire communication devices per instructions provided with product. Mount in Poke-Thru per illustrations s

Página 4

4Pass & Seymour Network Wiring: Two Category 5e inserts provided with Cat. Nos. RC4A and RC4C,other modules shown not included, sold separately.

Página 5

The RC4TC Series Poke-Thru Device is UL Listed and Classified to U.S. and Canadian safety standards to the following conditions: The RC4STC Poke-Thru

Página 6 - Carpet Cutout Template

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6

Modelos relacionados RC4KTCGY | RC4KTCVY | RC4KTCAL | RC4KTCBS | RC4KTCAB | BZTPP Series | RC3APTCBK | RC3APTCGY |

Mais documentos para Hardware Legrand RC4KTCBK

Para ver o documento Legrand RC4KTCBK Manual do Utilizador

Legrand RC4KTCBK Manual do Utilizador (4 páginas)

Comentários a estes Manuais

Sem comentários

Legrand RC4KTCBK Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Legrand RC4KTCBK. Legrand RC4KTCBK User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados RC4KTCGY | RC4KTCVY | RC4KTCAL | RC4KTCBS | RC4KTCAB | BZTPP Series | RC3APTCBK | RC3APTCGY |

Mais documentos para Hardware Legrand RC4KTCBK

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Legrand RC4KTCBK